TOSHIBA SD-P400014-inch LCD TV/DVD COMBINATION_UNLOCK_DISC REMOVAL AT EMERGENCY_DVD MECHANISM DISASSEMBLE PROCEDURE
DISC REMOVAL METHOD AT NO POWER SUPPLY
> Remove the Back Cabinet.
> Slide the Rack Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1)
> Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.
> Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.
PARENTAL CONTROL - RATING LEVEL - 4 DIGIT PASSWORD CANCELLATIONS
If the stored 4 digit password in the Rating Level menu needs to be cancelled
> Turn Unit ON.
> Press and hold the '7' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> The On Screen Display message 'PASSWORD CLEAR' will appear.
> The 4 digit password has now been cleared.
> Press and hold the '7' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> The On Screen Display message 'PASSWORD CLEAR' will appear.
> The 4 digit password has now been cleared.
TRAY LOCK
Tray cannot be opened by setting the Tray Lock.
> Turn Unit ON.
> Set the DVD to the Stop Mode.
> Press and hold the '9' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting.
> Set the DVD to the Stop Mode.
> Press and hold the '9' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting.
NB:No indications on the screen when the Tray Lock is setting.
To unlock the Tray Lock,
> Turn Unit ON.
> Set the DVD to the Stop Mode.
> Set the VOLUME to minimum.
> Press and hold the 'REC/OTR' button on the front panel.
> Simultaneously press and hold the '4' key on the remote control unit.
> Hold both keys for more than 2 second.
> The On Screen Display message 'INITIALIZE COMPLETE' will appear.
The Tray Lock has now been cleared.
> Set the DVD to the Stop Mode.
> Set the VOLUME to minimum.
> Press and hold the 'REC/OTR' button on the front panel.
> Simultaneously press and hold the '4' key on the remote control unit.
> Hold both keys for more than 2 second.
> The On Screen Display message 'INITIALIZE COMPLETE' will appear.
The Tray Lock has now been cleared.
NB:The above procedure will reset ALL of the player's settings to the default factory state.
DVD MECHANISM DISASSEMBLE PROCEDURE
LOADING MOTOR ASS'Y/START SW PCB ASS'Y/ END SW PCB ASS'Y
* Remove the 3 screws 1.
* Remove the Loading Motor Ass'y.
* Remove the 2 screws 2.
* Remove the Motor and Loading Worm.
* Disconnect the following connector: (CP2).
* Remove the screw 3.
* Unlock the 2 supports 4 and remove the Start SW PCB Ass'y.
* Unlock the 2 supports 5 and remove the End SW PCB Ass'y.
* Remove the Loading Motor Ass'y.
* Remove the 2 screws 2.
* Remove the Motor and Loading Worm.
* Disconnect the following connector: (CP2).
* Remove the screw 3.
* Unlock the 2 supports 4 and remove the Start SW PCB Ass'y.
* Unlock the 2 supports 5 and remove the End SW PCB Ass'y.
NOTE: In case of the Loading Worm installation, check if the value of the Fig. 2-1-B is correct.
When installing the wire, install it correctly as Fig.
When installing the wire, install it correctly as Fig.
TRAVERSE UNIT ROD/TRAVERSE UNIT HOLDER/CD DECK/INSULATOR
* Remove the screw 1.
* Remove the Traverse Unit Rod.
* Remove the 2 screws 3.
* Unlock the 2 supports 4 and remove the CD Deck Block.
* Remove the 2 screws 5.
* Unlock the 2 supports 6 and remove the Traverse Unit Holder.
* Remove the 4 Insulators.
* Remove the Traverse Unit Rod.
* Remove the 2 screws 3.
* Unlock the 2 supports 4 and remove the CD Deck Block.
* Remove the 2 screws 5.
* Unlock the 2 supports 6 and remove the Traverse Unit Holder.
* Remove the 4 Insulators.
MOUTH ASS'Y
Remove the 2 screws 1.
Remove the Mouth Ass'y.
Remove the Mouth Ass'y.
DISC L LEVER/DISC STOPPER/LOCKER STOPPER/ ROLLER GEAR
* Remove the screw 1.
* Remove the Disc L Lever and Disc L Lever Spring.
* Remove the Stopper Spring.
* Unlock the support 2 and remove the Locker Stopper.
* Unlock the support 3 and remove the Disc Stopper.
* Remove the Upper Roller, Roller Rubber and Roller Gear
* Remove the Disc L Lever and Disc L Lever Spring.
* Remove the Stopper Spring.
* Unlock the support 2 and remove the Locker Stopper.
* Unlock the support 3 and remove the Disc Stopper.
* Remove the Upper Roller, Roller Rubber and Roller Gear
* In case of the Upper Roller installation, install correctly as Fig.
RACK LOADING/RACK GEAR/GUIDE ARM SPRING/MID RACK GEAR
> Remove the Guide Arm Spring.
> Unlock the 3 supports 1 and remove the Rack Loading.
> Remove the Rack Gear and Mid Rack Gear.
> Unlock the 3 supports 1 and remove the Rack Loading.
> Remove the Rack Gear and Mid Rack Gear.
LINK R ASS'Y/LINK L/LINK MID/LINK SPRING
* Remove the screw 1.
* Remove the Link Spring.
* Unlock the support 2 and remove the Link L.
* Unlock the support 3 and remove the Link Mid.
* Remove the screw 4.
* Unlock the 4 supports 5 and remove the Link R Ass’y
* Remove the Link Spring.
* Unlock the support 2 and remove the Link L.
* Unlock the support 3 and remove the Link Mid.
* Remove the screw 4.
* Unlock the 4 supports 5 and remove the Link R Ass’y
ARM ROLLER ASS'Y/MID ROLLER 1/2 GEAR/TERMINAL GEAR
> Remove the screw 1.
> Remove the Arm Roller Ass'y.
> Remove the Terminal Gear and Mid Roller Gear 1.
> Unlock the support 2 and remove the Mid Roller Gear 2.
> Remove the Arm Roller Ass'y.
> Remove the Terminal Gear and Mid Roller Gear 1.
> Unlock the support 2 and remove the Mid Roller Gear 2.
CLAMPER ASS'Y/DISC GUIDE ARM/DISC R LEVER
* Unlock the support 1 and remove the Clamper Ass'y.
* Unlock the support 2 and remove the Disc Guide Arm.
* Unlock the support 3 and remove the Disc R Lever.
* Unlock the support 2 and remove the Disc Guide Arm.
* Unlock the support 3 and remove the Disc R Lever.
When installing the Clamper Ass'y, check if the Clamper Ass'y is locked correctly as Fig
EXPLODED VIEW
CLICK ON THE PICTURES TO MAGNIFY