Total output power ......... 300 W RMS(30%THD)
Frequency Response .....180Hz – 18kHz / ±3 dB
SPEAKERS
System ......................... Full range satellite
Speaker impedance .......8 ohm(centre),4 ohm(Front/Rear)
Speaker drivers ..............3” full range speaker
Frequency response .......150 Hz – 20 kHz
Dimensions
-Center……………………100 x 100x 75 (mm)
-Front/Rear..……………100 x 100x 75 (mm)
Weight
-Center…………………0.38kg
-Front/Rear…………….0.38 kg/each
SUB-WOOFER
Impedance .................8 ohm
Speaker drivers .......... 165mm (6.5”) woofer
Frequency response ...45Hz – 150 Hz
Dimensions ................122.6x 30 9.5 x 369 (mm)
Weight .......................3.54kg
![]()
![]()
![]()
![]()
![]()
![]()
Frequency Response .....180Hz – 18kHz / ±3 dB
SPEAKERS
System ......................... Full range satellite
Speaker impedance .......8 ohm(centre),4 ohm(Front/Rear)
Speaker drivers ..............3” full range speaker
Frequency response .......150 Hz – 20 kHz
Dimensions
-Center……………………100 x 100x 75 (mm)
-Front/Rear..……………100 x 100x 75 (mm)
Weight
-Center…………………0.38kg
-Front/Rear…………….0.38 kg/each
SUB-WOOFER
Impedance .................8 ohm
Speaker drivers .......... 165mm (6.5”) woofer
Frequency response ...45Hz – 150 Hz
Dimensions ................122.6x 30 9.5 x 369 (mm)
Weight .......................3.54kg
System , Region Code , etc. Setting
System Reset
a) Press “SETUP“ button on RC,TV will show setup menu
b) Select the menu using the▼ and► on RC
c) Go preference page to do system reset.
a) Press “SETUP“ button on RC,TV will show setup menu
b) Select the menu using the▼ and► on RC
c) Go preference page to do system reset.
Region Code Change [Only a qualified service person should reprogram the Region Code.]
a) In open model, press”9” “9“ “9“ “9“ on R/C, then input desired number to change region code :
1 USA
2 EU
3 AP
4 Australia ,NZ , Latam
5 Russia , INDIA
6 CHINA
a) In open model, press”9” “9“ “9“ “9“ on R/C, then input desired number to change region code :
1 USA
2 EU
3 AP
4 Australia ,NZ , Latam
5 Russia , INDIA
6 CHINA
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.
Top of DVD mechanism
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.
LOCATION OF PCB BOARDS
Version Control Change
In open model, press “1“ “5“ “9“ on RC
a) Press “SETUP“ button on R/C,TV will show se
b) Press► and select version you want using▼
c) Press and “ok” button to confirm
d) TV will show message as below:
SMPS circuit diagram and PWB
Password Change
a) Press “SETUP“ button on R/C,TV will show setup menu
b) Select the menu using the▼ and► on RC
c) Go preference page select “password“ to change
* 136900 is default password supplied.
a) Press “SETUP“ button on R/C,TV will show setup menu
b) Select the menu using the▼ and► on RC
c) Go preference page select “password“ to change
* 136900 is default password supplied.
Check on the Software Version
a) Press “SETUP“ button on R/C,TV will show setup menu
b) Select the menu using the▼ and► on RC
c) Go preference page select “Version Info“.
TV will show the version on screen.
Trade model
a) Press “Open/Close “ button on RC
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA OFF“
Upgrading new software
a) Copy “software “files” into a CD-R or USB flash drive.
b) Insert the CD-R disc or USB flash drive.
c) Press DISC or USB, the system will identify the update file automatically.
d) VFD will show “Updating“until update is complete.
* the system will switch off to standby automatically after update is complete.
e) OSD will show > “Upgrade file detected; Upgrading”
b) Insert the CD-R disc or USB flash drive.
c) Press DISC or USB, the system will identify the update file automatically.
d) VFD will show “Updating“until update is complete.
* the system will switch off to standby automatically after update is complete.
e) OSD will show > “Upgrade file detected; Upgrading”