UOC-TOP configuration instructions: NT11106PC201AG
In the following NXP or Trident Micro-Jungle:
TDA11105PS, TDA11106PS, TDA11115PS, TDA11126PS, TDA11145PS, TDA12135PS, TDA12136PS, TDA12165PS, TDA12196PS
Technical description
Introduction to UOC-TOP technology (series TDA11106PS)
The TDA11106PS / N2 series mainly adopts the form of pin package SDIP64 With the following:
* 200 channels in memory
* Image processing includes brightness control, contrast control, control color, system color control, image enhancement and five image modes.
* Users can edit the LOGO, show the LOGO when starting up and without signal
* Have the perpetual calendar and the game function.
* New OSD style, compatible with English, Thai, Vietnamese, Indonesian, Persian, Turkish, French, Bulgarian, Russian, Portuguese, Roman, Spanish, Italian, German, Dutch, Swedish, Norwegian, Hungarian, Polish, Czech, Slovenian, Croatian, Macedonian, Serbian, Greek, Kenyan
* Compatible with the FS and VS tuner
* With the screen change function, the up and down mode, and the left mode and Right is optional.
* The AKB function of all products is optional. When AKB is disabled, the energy in the cost of use can be reduced
* Added the left and right line suppression setting for an easy configuration of different parameters of the image tube
* Added CORING and the black extension in the image processing, obviously the image quality is improved.
Description of IC pins
Chip peripheral controller TDA11106 PS: EEPROM: 24C08
Remote control IC: NEC code / SANYO code. The factory debugs instructions.
How to enter the Factory mode (Service Mode): input method
Method 1: in normal use, press the [MENU] key, the menu is displayed "Image". When it is displayed, press the numeric keys "6, 4, 8, 3" in sequence and the television enters the factory mode.
Method 2: use the [PROOF] button on the factory-specific remote control:
Remote control of the NEC code, press the [PRESET] key first, then press the [TEST] key within 2 seconds, the TV enters production mode and the screen shows the production mode indicator.
Remote control of the SANYO code, press the [TEST] button, the TV enters production mode, display screen, show tips for the mode of production.
Press [TEST] or [POWER] to switch from production mode to status normal work.
Press [- / - -] in the [PROOF] state to enter the [BUS OPEN] state.
Under [BUS OPEN], press the [- / - -] key to return to the factory state.
Enter the debug / configure menu method
*User debugging menu: press the [TEST] or [MENU] key plus the numeric key "6, 4, 8, 3", enter the white balance debug state " B / W BALANCE "and then press [TEST] or [Display] to enter the "M0" menu, then press the [MUTE] button to enter the "M1" menus and "M2"
* User configuration menu: set "SETUP SELECT" in the menu "M2" to "1", press the [MENU] key again to enter the "M3" menu ~ "M9".
* In the "M0" ~ "M9" state, press the [Display] button to enter "FACTORY" mode.
Description of the debugging project of the menu: Factory.
Image debugging menu, take the PHILIPS / PAL test card (or select the built-in verifier signal).
*V.SLOPE adjustment so that the horizontal centerline of the test card is in the upper part of the piece.
* Adjust V.POSI so that the vertical center of the image is consistent with the vertical center of the CRT
* Adjust V.SIZE so that the vertical amplitude of the image complies with the requirement, and the re-emphasis rate = 90%
* Adjust VSC to make the vertical correction of the best image S
* Adjust H.PHASE so that the horizontal center of the image is consistent with the horizontal center of the CRT
H.BLK.L (0 ~ 15), you can adjust the line erase position to the left
H.BLK.R (0 ~ 15), you can adjust the line cutting position on the right side
* Take the PHILIPS test card (NTSC) and adjust the 60 Hz value to the base original 50 Hz. On the basis of increase or decrease.
Adjust the white balance (after the values recommended in the table)
*in "TEST.S" select the signal with the remote control.
* Then select the item "VSD", press the "V +" button to enter the state of the horizontal line.
* The numeric key "2" reduces "R.BIA", the numeric key "3" increases "R.BIA"
* The numeric key "4" reduces "G.BIA", the numeric key "5" increases "G.BIA"
* The number key "6" reduces "B.BIA", the number key "7" increases "B.BIA"
* When adjusting to white, adjust potentiometer G2 on the FBT so that on the screen appears one line horizontally, then press the "V +" button to return to full screen status
* Set the values of "R.DRV, G.DRV, B.DRV" until it reaches the desired level.
Adjust white balance 2 (after setting the recommended values in the table)
*First in "TEST.S" select the signal with the remote control.
or Select "R. BIA ", press [Display] to display a horizontal line
*Press the "V +" and "V-" keys to adjust the compensation. Press the keys "P +" and "P-" for any of the following options: R. BIA, G. BIA and B. BIA
*When adjusting to the white, adjust potentiometer G2 on the FBT so that the screen appears one line horizontally, then press [Display] to return to full screen status
*Set the values of "R.DRV, G.DRV, B.DRV" until it reaches the desired level.
The temperature of the color sought.
*Take the signal of the VH color bar of 60dB (1mv) and adjust the menu value AGC (high or low voltage). The noise in the image is gradually reduced until the noise simply disappears. At that moment, the tension of the point of TP-AGC test, and the voltage is the desired AGC voltage. This tension is the tension of AGC adjustment of the machine in the future.
*When "SETUP SELECT" is set to "1", press the "Mute" button to enter between the menus after "M2". Get in.
Start LOGO input method: LOGO edit
In M_MODE, press [Display] to enter the editing status of the LOGO.
Operation
Press [1] / [2]: Vertical position adjustment of the LOGO, [1] above, [2] below;
Press [3] / [4]: horizontal position adjustment LOGO, [3] to the left, [4] to the right;
Press [5] / [6]: Color selection of LOGO character, [5] adjust the first color of line, [6] adjust the second color;
Press [7] / [8]: Adjust the character size of the LOGO, [7] adjust the first line size, [8] adjust the second line large or small
Press [0]: Delete the entered letter
Press [up arrow] / [down arrow]: LOGO character selection (0 ~ 9; A ~ Z; a ~ z; ":. + - * / @", SPACE);
Press [arrow to the left] / [arrow to the right] to move the cursor;
Press the [Display] key: Exit the LOGO editing status, the information of the LOGO is stored in EEPROM, returns M_MODE;
When the tuner is used without band change, PIN 28 is the UHF output, PIN 30 is the VHF-L output and PIN31 is a VHF-H output, all are "output from OPEN DRAIN ", and they need to connect a pull-up resistor to 5V.
* When [HALFTONE] and [MENU BG] are all "ON", the interface OSD is of semi-transparent brightness.
* When [HALFTONE] is "ON" and [MENU BG] is "OFF", the interface OSD is completely transparent
* When [HALFTONE] is "OFF" and [MENU BG] is "ON", the OSD interface is opaque.