For repair information on the SD4.00SA DVD Module, refer to Service Manual "DVD Module SD-4.00SA_CH - 3122 785 12480".
For repair information on the Subwoofer SW8000SA/00S, refer to Service Manual "SW8000SA/00S/01S/17S - 3139 785 30099"
Output power (6 ohm, 1kHz, 10% THD) L & R, Center, Surround : 40W RMS / channel
Amplifier Frequency Response (-3dB) : 250Hz-32kHz
SOUND: JAZZ, ROCK, DIGITAL, CLASSIC [DRAMA, ACTION, SCI-FI, CONCERT]
[.....] Sound effect available when playing a DVD/VCD disc.
Input sensitivity
Aux in (at 1kHz) : 880mV ± 3dB
TV in (at 1kHz) : 350mV ± 3dB
Output sensitivity
Line out (Left/Right) : 0.6V ± 2dB at 100 kohm
Center out (Vol. Max.) : 500mV ± 2dB at 47 kohm
Subwoofer out (Vol. Max.) : 0.76V ± 2dB at 47 kohm
Headphone output at 32 ohm : 660mV ± 2dB (Vol. Max.)
Digital in : IEC 60958
Digital out : SPDIF Coaxial
Reprogramming of DVD version matrix [Only a qualified service person should do the reprogramming.]
After replacement/repair, the customer settings and also the region code may be lost.
Reprogramming will put the set back in the state in which it has left the factory, i.e. with the default settings and the allowed region code.
Reprogramming will put the set back in the state in which it has left the factory, i.e. with the default settings and the allowed region code.
Reprogramming is done by the Remote Control.
Complete version matrix to be enter is 'PLAY 159 XXX XXX XX PLAY'
Complete version matrix to be enter is 'PLAY 159 XXX XXX XX PLAY'
1) Ensure no disc is loaded in the tray.
2) Set the Remote Control to DISC source.
2) Set the Remote Control to DISC source.
3) Press <PLAY> followed by numerical keys <1> <5> <9>
Remark: Top left hand corner of the TV screen will display "X"for all these 4 keys that you have pressed.
4) Press now the following numerical keys (8 digits version matrix):
Remark: Nothing will be displayed on the TV screen for all these 8 digits that you have pressed.
Remark: Top left hand corner of the TV screen will display "X"for all these 4 keys that you have pressed.
4) Press now the following numerical keys (8 digits version matrix):
Remark: Nothing will be displayed on the TV screen for all these 8 digits that you have pressed.
for LX8200SA/22S : <2> <2> <2> <0> <3> <7> <0> <8>
5) Press <PLAY> again.
Caution: Wait for about 3 seconds for the set to reset to the required setting.
The TV screen will turn blue follow by a loud sound at the speaker output.
Caution: Wait for about 3 seconds for the set to reset to the required setting.
The TV screen will turn blue follow by a loud sound at the speaker output.
6) Disconnect mains to ensure proper reset.
How to check the version matrix and the software version number of the set:
1) Power up the set and select DISC source.
1) Power up the set and select DISC source.
2) Press <SYSTEM MENU> on the Remote Control to enter the User Preference Manual (UPM),
follow by pressing the following key:
- <Cursor Down> key 4 times
- <Cursor Right> key 1 time
- <Cursor Down> key 4 times
follow by pressing the following key:
- <Cursor Down> key 4 times
- <Cursor Right> key 1 time
- <Cursor Down> key 4 times
3) Message "(C)PHILIPS 01- 02 5580 W.WW.WW ...... PXXXXXXXX Y.YY.Y"will be displayed
on the TV screen:
on the TV screen:
W.WW.WW | - indicate the BEA software version number |
PXXXXXXXX - indicate the version matrix programmed | |
Y.YY.Y | - indicate the FEA (servo) software version number |
4) Press <SYSTEM MENU> on the Remote control to exit.
Setting the TV system default
Press <SYSTEM MENU> on the Remote Control to enter the User Preference Manual (UPM).
2) From the User Preference Manual on the TV screen, select TV SYSTEM to change the TV system default
accordingly as shown in the table below:
accordingly as shown in the table below:
Version /21R /21S /22S /30S /33S /37S | Region Region 3 Region 4 Region 2 Region 4 Region 3 Region 1 | TV system default AUTO NTSC PAL AUTO AUTO NTSC |
3) Press <SYSTEM MENU> on the Remote control to exit.
Power amplifier board circuit diagram
