Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected reactions that are best avoided. Before reaching into a powered TV set, it is best to test the high voltage insulation. It is easy to do, and is a good service precaution.
The melting temperature of lead-free solder is higher than that of leaded solder by 30ºC to 40ºC (54ºF to 72ºF). Use of a soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to the component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing this product especially when soldering large components, through-hole pins, and on PCBs as the level of heat required to melt lead-free solder is high.
Depending on the model, use an isolation transformer or wear suitable gloves when servicing with the power on, and disconnect the power plug to avoid electrical shock when replacing parts. In some cases, alternating current is also impressed in the chassis, so electrical shock is possible if the chassis is contacted with the power on.
How to enter and Exit from the SERVICE MODE
Press MUTE button once on Remote Control.
TV mode changes as follows. Un-Mute => Mute
Press MUTE button again and keep pressing. (Sound Mute is cancelled)
While pressing the MUTE button, press P à button on TV control panel. This is the way to enter the service mode. Letter S will appear at top right corner of the screen indicating that the set is in Service Mode. See the service mode screen below.
KEY FUNCTION IN THE SERVICE MODE and Test Signal Selection. The following key entry during display of adjustment menu provides special functions.
SELECTING THE ADJUSTING ITEMS
While displaying the adjustment menu, press the P UP button to cycle through the adjustment items in the order of table. (P DN button for reverse order)
ADJUSTING THE DATA
While displaying the adjustment menu, press the VOLUME + OR – button to change the value of data in the range from 00H to FFH. The variable range depends on the adjusting item.
HOW TO EXIT FROM SERVICE MODE
Press the [Exit] button on Remote.
ADJUSTING ITEMS IN THE SERVICE MODE
LED INDICATIONS FOR SERVICE - Software Upgrade and Error conditions indicated by the Power LED is described below.
How to ENTER the HOTEL MODE MENU
Open Main Menu by pressing Menu button of RCU.
2) Press the following password number “1048” with the button of Remote Control.
Note: Hotel Menu can be displayed to input the password number when there is focus in the first layer of Main Menu.
DISPLAY OF HOTEL MODE MENU
The Graphic Design and color of Hotel Mode Menu is the same as the User menu.
(Small differences which do not affect to operation will be acceptable)
- The language will follow the “Menu Language” setting in the menu.
OPERATING HOTEL MODE MENU
To enable Hotel Mode, press ▲or buttons to select “Hotel Mode” item and press u button.
Press ▲or buttons to select “On” and press OK button.
- Once Hotel Mode is “On”, the Hotel Mode settings will be enabled for adjusting.
- Press ▲or▼ buttons to select item of Hotel Mode Settings.
Press u and ▲or▼ buttons to select settings and press OK button.
See the table below for explanation of each setting.
Press Exit when finished adjusting the settings.
USB CLONE FUNCTION
Feature overview
Hotel Menu settings and Welcome Screen image, Picture settings, Default URL of Toshiba Cloud TV.
Services and Network settings should be copied to other TV by Hotel Menu “USB Clone Function”.
Welcome Screen image
・ File name: WelcomeScreen.jpg (case sensitive)
・ File type: JPEG
・ Color depth: 24bpp
・ Resolution: 1280 x 720
・ File size: 1MB or less
Note: The Welcome image is preserved besides the TOSHIBA logo (default). When user would like to copy Welcome Screen, the clone data should be exported to USB memory in advance and then put the Welcome Screen image into USB and start import Clone data from USB to TV.
< Default URL of Toshiba Cloud TV Services >
・ File name: hotelCloudConfig.txt (case sensitive)
*However, URL can be operated on the site specially developed.
・ File type: Text
Note: When user would like to copy “URL of Toshiba Cloud TV Services”, the clone data should be exported to USB memory in advance and then put “hotelCloudConfig.txt” file into USB and start import Clone data from USB to TV.
Copying data form TV to USB
Press “OK” on “Start USB Clone” button of “USB Clone Function”, USB Clone mode initial window [1-1] is displayed.
The options below are selected by left and right keys in this window.
USB to TVà Copy setting data in USB memory to TV.
TV to USBà Copy TV settings to USB memory.
(2) Insert USB memory, select “TV to USB” [1-2] and press [OK] key.
(3) The now copying window [1-3] will be displayed.
(4) Wait for window that indicates the copying process is complete before removing the USB drive.
To write data form USB to TV
(1) Press “OK” on “Start USB Clone” button of “USB Clone Function”, USB Clone mode initial window [2-1] is displayed.
(2) Insert USB memory, select USB to TV [2-1], and press [OK] key.
(3) The window [2-3] will be displayed.
(4) When the copying has finished successfully, the message "The TV will reboot when this window is closed." will be displayed. If the copying is not successful, an error message will be displayed.
(5) Exit the menu and the TV will reboot.
(6) Remove the USB memory.
MAIN BOARD EXCHANGE
When Main board is exchanged, the Application SW (Firmware) and Model Setting need to be updated and the serial number needs to be written the serial number into Main Board (see “WRITING SERIAL NUMBER INTO MAIN BOARD”).
Please update in the following procedures.
Updating of Software and Model Setting
Copy the Application SW (Firmware) file and the Model Setting file to the root of the USB mass storage device.
Note : Please use the USB mass storage device formatted with “FAT32”
Unplug TV, and then insert the USB mass storage device to the USB slot of the TV.
Note : Please unplug TV after turning ON TV by "Power" key on remote control.
3. During pressing “-” key of side key on TV, plug TV.
Note : Please continue pressing "-" key until "Software upgrade in progress." appears on a screen.
After updating complete, unplug TV and remove the USB mass storage device.
Plug TV, then check the updating by using self check screen.
Refer to “Confirmation of Software updating” section on next page.
6. Update to the newest SW.
This model can be updated from aerial or network to the newest Software.
Refer to the user manual of this model for the updating method.
Confirmation of Software updating
Check the TV Model and Model Info by using self check screen.
1. Press SETUP on Remote Control.
2. Select “Get Help” >> “System Information”
3. Press “3” “5” “7” “4”
Self check screen is displayed.
WRITING SERIAL NUMBER INTO MAIN BOARD
When the board is broken, service man will go to customers home and change the board. After change the board service man has to put the serial number same as before. So the service man will use the PC and write the serial number to USB mass storage device. After that the service man will plug the USB mass storage device to the TV and write the serial number to the TV.
Create the ini file by Text Editor.
File Name: Service Serial Number Writing.ini
File Format: Plain Text.
Write two lines, "[serial number]" and a serial number, using the text editor on Windows.
For example, when a serial number is "C37222T00008L1":
[serial number]: C37222T00008L1
2. Use the USB mass storage device formatted with “FAT32”.
3. Copy the "ServiceSerialNumberWriting.ini" file to the root directory of the USB mass storage device.
Enter Service mode.
1. Press the MUTE button once on Remote Control. TV mode changes as follows. Un-Mute => Mute
2. Press the MUTE button again and keep pressing.
3. While pressing the MUTE button, press P à button on TV control panel.
5. Insert the USB mass storage device to the USB slot of the TV set. Writing starts.
After finish writing the “OK” and “Serial number” appear on TV.
Unplug USB mass storage device.
8. Check the serial number by using self check screen.
How to enter the self check screen.
1 Press SETUP on remote control unit.
2 Select “Get Help” >> “System Information”
3 Press “3” “5” “7” “4”
