How to make Service remote control unit by supplied remote control unit
- Prepare normal remote control unit. (Part No. NE601UE)
- Remove 3 Screws from the back lid.
- Add J1 (Jumper Wire) to the remote control CBA.
How to enter the service mode:
Use the service remote control unit.
- Turn the power on. (Use main power on the TV unit.)
- Press [SLEEP] button on the service remote control unit. Version of microcomputer will display on the CRT. (Ex: 058-0.06)
- Check the display on the lower left is “3641” and if it is not “3641,” set it at “3641” according to "Initial Setting"
- Enter the Service mode.
- Press [VOL n] button on the service remote control unit. Display changes “C/D,” “7F,” “SOUND TYPE,” “VIDEO,” “1000,” “YUV MEMORY,” “TUNER A/M/S,” “QAM,” “DTV-H,” “D-SOUND,” and “DL V-CHIP” cyclically when [VOL n] button is pressed.
- 7F --- Set to “FF.”
- SOUND TYPE --- Set to “MONO.”
- VIDEO --- Set to “V1/V2.”
- 1000 (monitoring time) --- Set to “1000.”
- YUV MEMORY --- Set to “OFF.”
- UTUNATSMS001: Set it in “M.”
- UTUNATSSP001: Set it in “S.”
- QAM --- Set to “135.”
- DTV-H --- Set to “B.”
- D-SOUND --- Set to “STEREO.”
- DL V-CHIP --- Set to “ON.”
Setting for BRIGHT, CONTRAST, COLOR, S-COLOR, C-COLOR, TINT, V-TINT, S-TINT, C-TINT, SHARP, S-SHARP, and C-SHARP Data Values.
- Enter the Service mode.
- Press [MENU] button on the service remote control unit. Display changes “BRT,” “CNT,” “CLR,” “S-CLR,” “C-CLR,” “TNT,” “V-TNT,” “S-TNT,” “CTNT,” “SHARP,” “S-SRP,” and “C-SRP,” cyclically when [MENU] button is pressed.
- Press [MENU] button on the service remote control unit. Then select “CONTRAST” (CNT) display.
- Press [CH ▲▼] buttons on the service remote control unit so that the value of “CONTRAST” (CNT) becomes 84.
Use the same way as stated above, and adjust the values to the following
CLR => 58
S-CLR => 58
C-CLR => 66
TNT => 54
V-TNT => 58
S-TNT => 58
C-TNT => 59
SHARP => 43
S-SHARP => 40
C-SRP => 40
SD CHECK MODE
- Enter the Service mode.
- Press [1] button on the remote control unit. The unit enters the SD-Check mode.
- The unit starts selecting the added channel from the first channel according to the memorized CH ADD/DEL data and CATV/TV data in RAM.
SOFTWARE RESET
To reset software, press [5] button on the remote control unit for at least 5 seconds after pressing [CH RETURN] button on the remote control unit.
INITIALIZATION
To put the program back at the factory-default, initialize the television as the following procedure.- Use the service remote control unit.
- Turn the power on. (Use main power on the TV unit.)
- Press [SLEEP] button on the service remote control unit to enter the Service mode. (Refer to “How to enter the Service mode” )
- Press [VOL▼] button on the service remote control unit twice, and confirm that OSD indication is “7F = FF.” If needed, set it to become “7F = FF” by pressing [CH▲/▼ ] buttons on the service remote control unit.
- Confirm that OSD indication on the four corners on TV screen changes from on and off light indication to red by pressing a [DISPLAY] button. (It takes one or two seconds.)
- Turn the power off by pressing main power button on the TV unit, and unplug the AC cord from the AC outlet.
POWER SUPPLY [SMPS] SCHEMATIC
CLICK ON PICTURE TO ZOOM IN
UNIVERSAL REMOTE CONTROL SET-UP CODES
GE UNIVERSAL REMOTE: 0004 0009 0044 0135 0049 0051 0189 0053 0147 0039 0130 0227 0233 0250 0252 0254 0257 0265 0266 0310 0325 0456 0040 0041 0042 0021 0023 0024 0179 0045 0025 0027 0030 0032 0034 0035 0037RCA RCR 311W: 1003, 1004, 1009, 1011, 1018, 1021, 1023, 1025, 1026,1028, 1030, 1031, 1033, 1035, 1038, 1039, 1041, 1045,1047, 1054, 1078, 1083, 1109, 1123, 1127, 1128, 1133, 1163, 1165, 1167, 1206, 1207, 1208, 1230
RCA RCR 312W: 10017, 10154, 10451, 10236, 10463, 10180, 10178, 10171, 11394, 11963
ALL OTHER BRANDS: 1051 1061 1075 10521091 1147 1195 1145 1120 1225 1012 1231 1002 1317 1032 1184 1298 1287 1288 1171