- Hold press "UP" button until the "Lamp hours info." OSD display on bottom-right of screen.
- Press keypad “Power” and “Blank” key simultaneously again, then enter Factory menu.
DMD LAYER
CW delay: Adjust color wheel delay.(Note this value before upgrade software)
White peak: Adjust DMD white peak. In PC mode default value set 10, in Video mode is 0. Software auto set this value as source find.
DLP Brightness: Adjust DLP Brightness. Default setting is 36.Do not change this value.
DLP Contrast: Adjust DLP Contrast. Default setting is 30.Do not change this value.
Burn-In Hour: set how many hours to burn-in. Projector will enter burn-in mode on next selection.
Burn-In: After you set burn-in hours, set this selection to “On” and system will enter going to burn-in immediately. Projector will run color change (Red, Green, Blue, Black, White) on screen. System will auto turn off after burn-in hour count down to 0 and burn-in complete.
(You can also cancel burn-in sequence by set this selection to “Off”).
ADC LAYER
ADC Brightness: ADC brightness auto calibration black.
ADC Contrast: ADC contrast auto calibration white.
ADC Offset RGB: value to tell you calibrate result.
ADC Gain RGB: value to tell you calibrate result.
Fac Brightness: adjust default brightness value in source PC.
Fac Contrast: adjust default contrast value in source PC
COLOR LAYER
When Source is YPbPr (Never Change these setting) (Note these values Before Upgrade Software)
PbPr G Offset : combine with user OSD brightness in YPbPr
PbPr G Gain:combine with user OSD contrast in YPbPr
PbPr R Offset: offset of color red
PbPr G Offset: offset of color green
PbPr R Gain: saturation R
PbPr B Gain: saturation B
6500,11500 R,G,B: 6500K/11500k submenu
(Never Change these setting)
6500 R: gain of color red while color temp is 6500
6500 G: gain of color green while color temp is 6500
6500 B: gain of color blue while color temp is 6500
6500 R: gain of color red while color temp is 11500
11500 G: gain of color green while color temp is 11500
11500 B :gain of color blue while color temp is 11500
PC 9300 and Video 9300: 9300K submenu. (Never Change these setting)
PC 9300 R: gain of color red while PC color temp is 9300
PC 9300 G: gain of color green while PC color temp is 9300
PC9300 B: gain of color blue while PC color temp is 9300
Video 9300 R: gain of color red while Video color temp is 9300
Video 9300 G: gain of color green while Video color temp is 9300
Video 9300 B: gain of color blue while Video color temp is 9300
OPTIC LAYER
Test Pattern: system auto produce pattern for engineer test.
Spoke light: unit display full white.
Curtain Red: unit display full color red.
Curtain Green: unit display full color green.
Curtain Blue: unit display full color blue.
LAMP LAYER
Interpolation: De-interlace Mode
Filter: system auto select Filter.
Lamp Hour: value to tell you lamp usage hours.
Usage Hour: value to tell you unit usage hours.
Fac Lamp Hours: Record all of the amp usage hours
Data Reset: Reset all data to default include factory assign value. [Never try to reset all data.]
OTHER LAYER
Gamma index: system auto select DLP gamma index
Gray value: adjust here to check DMD fail pixel.
Blue value: adjust here to check DMD fail pixel.
Scaling: tell you what scaling mode is using now.
Pc/PbPr Mode: index of input timing
RS232: Enable / Disable RS232 control.
FAN LAYER
T1-DMD: DMD sensor temperature
T2-Lamp: Lamp sensor temperature
T3-Blwr: Blower sensor temperature
F1-Lamp:Lamp fan speed in RPM
F2-Blst:Blaster fan speed in RPM
F3-Blwr :Blower fan speed in RPM
Manual Fan Speed: Change fan speed by manual.
SOG Threshold : Change SOG threshold level of AD
More Options: Change to Fac7 submenu
