FAULT CODES
NP1 | No Picture and No Sound in TV mode | • Make sure the Power cord and Aerial Cable are properly connected . • Make sure the batteries in remote control are not flat. • Press the POWERbutton to switch the TV on. • Switch to TV source by pressing “TV” button. • Run “Automatic Search ” by operating the remote control |
NP2 | No Picture and No Sound in video mode. | • Check the connection between the optional video equipment and the TV. • PressSCART , Video/S-V orCOMPONENTbutton on the remote control to select the right video equipment. |
NP3 | TV is automatically turned off | • Check if the “SLEEP” timer is activated . • Press the POWERbutton to turn on the TV once again |
PP1 | Double Images /Ghosts | If the TV suffers interference from signals reflecting from mountains or buildings , double-pictures or Ghosts will occur. • Adjust the aerial’s location and direction • Replace it with one with better directionality. • Turn off or disconnect the booster if it is in use , as the booster may be inappropriate |
PP2 | Snowy picture and noisy Sound | If snow totally blocks out the picture , there may be a problem with the Aerial or Aerial Cable . • Have the TV and aerial been connected properly ? Has the aerial cable been damaged ? • Is the aerial pointing in the right direction ? • Is the aerial itself faulty ? • Try using a booster , as signal transmission may be low |
PP3 | Distorted picture and noisy sound | • Turn off or disconnected the booster if it is in use , as broadcast signals may be too strong |
PP4 | Dotted Lines / Stripes in the picture | If the TV or aerial suffers interference from other equipment , stripes or noise may appear in the picture. • Keep the TV away from noise sources such as personal computer , amplifier , cars, motorcycles or hair-dryers. • If the aerial suffers interference from a radio tower or high-voltage wire , contact the local dealer. |
PP5 | Stripe noise . | • Check the coaxial cable connected with the TV is not oxidized • Do not use 300 ohm twin lead cables as interference may occur • It is recommended to use a 75 ohm coaxial cable (not supplied) to get premium quality picture. • Keep the aerial cable away from other connecting cables |
PP6 | No color, too light or too dark | • Adjust the picture settings - APC, Brightness, Contrast, Saturation , Color Temp. • Press “RESET ” button on remote control |
NS1 | Good picture, no sound | • Make sure the headphone is not connected. • Check audio connections between Equipment & LCD-TV. • PressMUTEor VOL+ to cancel the muting. |
NS2 | • Make sure that the aerial connected is 75 ohm coaxial cable (not supplied) , not 300 ohm twin lead cables . • Keep the aerial cable away from other connecting cables. • Press SOUNDto select “Mono” which will reduce the noise. • Adjust BASSor TREBLEproperly in OSD. | |
NS3 | No sound in TV mode | If the Country setting for the TV is incorrect , it may prevent the sound from being issued • Select the Countrywhere you are located in OSD Menu. • If the country is not listed in OSD , select “Other Country”. |
NS4 | Good picture, but noisy sound or no sound in TV mode. | • If the sound of “all the channels” is noisy , run A.P.S. again by selecting Automatic Searchin OSD. • If the sound of “some channels” is noisy or no sound , select Manual Search and select an appropriate TV systemin OSD such as B/G , D/K , I , L/L’ ; then , store it. ( If the sound system setting for a TV channel is incorrect , it may prevent the sound from being issued .) |
PC1 | PC display is Not Full Screen | • Select Auto Image Adjustin OSD menu to optimize the image . • If executing Auto Image Adjust still can not achieve full screen display, adjust V.Position and H.Position in PC mode |
PC2 | Horizontal Noise or Color pattern is not uniform | • Select Auto Image Adjust in OSD menu to optimize the image . • If still no good , adjust H. Phase in OSD menu |
PC3 | “Out of Range” message | • Maximum PC resolution supported is 1024x768 / 1280 x 768, so the screen will appear “Out of range” at higher resolution. • Reduce the resolution to 1024x 768/ 1280x 768 from PC . |
PC4 | No Sound | • Make sure PC audio Input is well connected. |
PC5 | “Not Available” message on PIP | • If Main-Display is PC and Sub-display is Component , resolution of the PC should be reduced to 800 x 600 or lower ;then , the PIP will work well. |
PC6 | After“No Signal ”has appeared on PC mode for a while, the view disappears and the “ LED Indicator” turns from Green to”Red”. | • Press any key on keyboard or move the mouse to activate the PC , because the PC may go to power saving status. • Check if the D-sub connector (Cable) is disconnected or loose . |
RC1 | Remote Control does not work | • Make sure the batteries in remote control are not flat • Check the polarity of the batteries • Use the remote control in the front of the TV or from less than seven meters away. • make sure the Remote Sensor Window is not under strong lighting |
RC2 | Can not change channels with the remote control | • Press TV button to switch to TV mode. • Make sure the TV is not in Teletext mode |
PH1 | Picture suddenly Stops Responding or abnormal | • Press RESETbutton on remote control . • Unplug and then plug the Power Cord of the TV from the AC outlet (or the Adapter from the TV). • If the picture still no good , execute “Initial EEPROM”. Press POWERkey to turn off the TV . Press“CH DN” key on the top of LCD TV ( don’t release ) ; then, press POWER button on remote control until “Initial EEPROM” appears on the screen . (Note: Remind user that every setting will be return to factory preset mode including Child Lock , PIN No. , Programs) |
Power Start Not Good
Steps to Refresh EEPROM
- Press POWER key to turn off the LCD-TV.
- Press CH. Down key on the top of LCD-TV (don’t release) and then press POWER button on remote control, until “EEPROM Initial” appears.
- Now, all the buttons, which you are pressing, could be loosed.
If the PIN of Child-Lock is forgotten , the only way to unlock the channels is to refresh EEPROM and the PIN will also recover initial number “1111”. Besides , all the STORE done by user will be refreshed to the situation of First Time Installation.
FRAME DEFECTS OR STRIPED LINES AT ALL SOURCES
